Skip to main content

Why Is a Wheelchair Ramp 1:12? What It Means in Percent, Degrees and Feet

5 min read

TL;DR

  • Under the 2010 ADA Standards a ramp can be no steeper than 1:12, which is 8.33% or about 4.76°: one inch of rise for every foot of horizontal length.
  • Each inch of rise takes a foot of horizontal length: a 6-inch step needs 6 feet of ramp, and one ramp run may climb at most 30 inches.
  • Steep ramps are hard for some wheelchair users to push up and to stop on coming down. English guidance gives 1:12 to a 2 m ramp run and asks for 1:20 on a 10 m run.
  • Existing buildings with no room may go steeper only for small rises: 1:10 up to 6 inches and 1:8 up to 3 inches.

Under the 2010 ADA Standards, a ramp can be no steeper than 1:12: one inch of rise for every foot of horizontal length, or 8.33%. 1:12 is a ceiling, not a target. Each sloped section may climb 30 inches at most, and the ADA's notes ask for the gentlest slope that fits.

The ADA Standards cover government buildings, businesses open to the public and other commercial facilities, not the part of a private home that people live in. For a ramp at home, ask your local building department which rules apply.

What 1:12 is in percent, degrees and feet

A slope of 1:12 rises 1 unit for every 12 units across. A ramp run is one sloped section between two level landings. Percent is the rise divided by the horizontal length, and the angle follows from the same ratio.

SlopePercentAngleHorizontal length per inch of rise
1:812.5%7.13°8″
1:1010%5.71°10″
1:128.33%4.76°12″ (1 ft)
1:205%2.86°20″

At 1:12 the math is easy: each inch of rise takes a foot of ramp. A 6-inch step needs 6 feet. A ramp run that climbs the full 30 inches covers 30 feet of floor, plus a level landing at the top and bottom.

Where 1:8, 1:10 and 1:20 come in

The Americans with Disabilities Act (ADA) Standards use each of these numbers for a different case.

  • 1:12 is the limit for a ramp run. One run can rise 30 inches at most. Each run needs a level landing at the top and bottom, at least 60 inches long, and the ramp is at least 36 inches wide. A run that rises more than 6 inches needs handrails on both sides.
  • 1:10 and 1:8 are only for existing buildings without room for 1:12. A ramp at 1:10 may rise up to 6 inches, and one at 1:8 up to 3 inches. Nothing may be steeper than 1:8.
  • 1:20 is the line between a walkway and a ramp. A walking surface steeper than 1:20 counts as a ramp, so it needs the ramp rules.

Why ramps can't be steeper

The notes that come with the ADA rules ask for the least slope possible, so that the ramp works for the widest range of users. They also ask for stairs next to the ramp where possible: for some people, such as those with heart disease or little stamina, a long distance is a bigger barrier than steps.

England's guidance for accessible buildings (Approved Document M) spells out what goes wrong on a steep ramp. Wheelchair users who lack the strength to push themselves up have trouble climbing it, and coming down, it is hard to slow down or stop. The same guidance also makes a longer ramp run gentler.

Length of one ramp runSteepest slopeHighest rise
2 m (6.6 ft)1:12166 mm (6.5″)
5 m (16.4 ft)1:15333 mm (13.1″)
10 m (32.8 ft)1:20500 mm (19.7″)

In England, 1:12 is the slope for a short 2-meter ramp run. Between the rows the limit is interpolated in proportion, so a 4 m run may be 1:14 and a 9 m run 1:19. The guidance keeps each run within 10 m and 500 mm of rise. A US ramp run at 1:12 can be 30 feet long, so the English guidance is stricter for long ramps.

Is an existing ramp within 1:12?

Divide the rise by the horizontal distance it covers. If the answer is 1/12 or less, the ramp is within 1:12. A porch ramp that rises 6 inches over 5 feet is 1:10, steeper than the limit. On the ramp itself the horizontal distance is hard to tape, so reading the floor with a phone slope level is easier. In PitchFall:

  1. Pick Ramp mode. In most regions, including the US, the slope shows as 1:n, and you can switch it to percent or degrees.
  2. The maximum is 1:12 by default. You can pick a gentler maximum, 1:16 or 1:20, or type your own.
  3. Stand the phone on its long edge on the ramp, pointing up the slope. Where the slope passes your maximum, it says TOO STEEP and shows the maximum, like "Max 1:12".
  4. A ramp is not always the same slope along its length, so check the bottom, the middle and the top.

The PitchFall introduction shows the screen and the unit settings.

Sources

A slope level that tells you how much to move it

Share